How emergency response to the emergency of hydraulic cylinder?

Use daily necessities for emergency response

Hydraulic cylinder using the emergency response is not allowed to have emergency measures, must be from the actual start: first, the production time is short; two is to ensure that traffic safety; three is not damage to the original device, does not cause damage to other parts; four is the emergency, to timely exchange of regular parts.

1 use bicycle parts emergency

1.1 if the diesel injector top rod inner hole of the ball is lost can use bicycle freewheel ball instead, can also be used instead of butter mouth scrap in the small steel balls.

1.2 when the agricultural vehicle clutch bearing return spring break, can use the bicycle seat under the tensile spring maintenance of hydraulic cylinder.

1.3 Dongfeng 12 walking tractor fixed steering fork and steering arm pin if the wear can be used bicycle crank turn pin instead.

1.4 in the tire filling and bleeding, often need to screw out the valve core, and sometimes due to improper use, or after a long use of the lower part of the valve core of the valve core is broken in the valve mouth, and the broken part of the more difficult to remove. Then, it is desirable a bicycle spoke, the screw thread is forced to break within the core of the valve into the screw, the spokes thread attack off the inner core, and then slamming the spokes outward pull out can be left in the valve fault core removal. This method is simple, have proved effective every time.

2 use of daily necessities emergency

2.1 cleaning engine oil bottom shell or body surface, if too much difficult to wash and iron impurities can be suction amount of dough from sticking.

2.2 when the gasoline engine carburetor float is damaged, can use the thermos bottle cork instead of restructuring.

2.3 if the motor vehicle brake fluid leakage, can be replaced with liquor or a certain concentration of soap.

2.4 toothpaste contains abrasive materials, can be used to grind the valve and valve seat of the valve, diesel engine three pairs of precision parts and motor vehicle lights on the glass on the glass.

2.5 household detergent, etc., can be used for cleaning machinery parts and components, especially suitable for cleaning rubber parts, after washing does not occur the phenomena of swelling and deformation.

2.6 for washing powder with sawdust with lubricating oil cleaning parts.

2.7 if it is found that the battery electrolyte level is too low, in order to prevent the plate sulfide, can buy the market of pure water, space water into the battery.

2.8 cut cans of shell, can be conveniently manufactured aluminum funnel washer motor vehicle or gas, water.

2.9 when found tank, oil cooler and hydraulic oil radiator multi core component damage resulting in oil spills, leakage and leakage, to quickly determine the damaged parts, can use cigarettes blowing method to locate the leak. Is lit a cigarette, take a deep breath, including smoke in the mouth, the suspect faulty tube (core) is blocked, alignment and the other end is blowing smoke, tube (core) on smoking is the fault parts, then find a part of hydraulic cylinder.

This method is simple, effective and reliable, but should pay attention to safety.

3 use electrical appliances emergency

3.1 if the diesel engine high pressure oil pipe joint oil leakage, cut a section of electrical fuse 16 is around the fastening nut.

3.2 if the magnetic motor is removed when the high voltage contact carbon rod, causing the magnetic motor can not generate high voltage power, can be used to dry the core of the battery to wear a short period of time. If the car distributor cap is damaged or lost the center electrode, can use 5 batteries in the carbon rod slightly after grinding substitute.

4 other emergency methods

4.1 if the high pressure pipe nipple leakage, can be used in plastic or soft metal piece cut into a small ring, pad in the joint cavity of the hydraulic cylinder.

4.2 when the generator carbon brush wear is excessive or insufficient spring force influence power can be sliced into carbon brush length and width of the same piece of wood or bark, pad between the spring and a carbon brush, in order to increase the contact pressure of the carbon brush and the commutator.

4.3 wire filter air filter can wash the loofah instead.

4.4 if the rubber seal self locking spring is too loose, can be made up by the method of adding rubber band.

4.5 parts of the joint surface commonly used sealing gasket seal, and in the gasket on a layer of oil resistant sealant to increase the sealing effect, but if there is no sealant, can also use the paint instead; the viscosity of the paint is larger and dry, so that the sealing is reliable, the effect is good. As a Nissan WD140-4 type bulldozer air pump failure and repair after installation due to the absence of sealant in the pump cover sealing pad is coated with a layer of paint, the certificate for the use of the effect is very good.